Search published articles


Showing 4 results for Solid State
SOLID STATE REDUCTION OF CHROMITE IN HIGH CARBON FERROCHROMIUM-CHROMITE COMPOSITE PELLETS
A. Ataie1,, S. Heshmati-Manesh1,, S. Sheibani1,, G. R. Khayati,y. Firozbakht,
Volume 5, Issue 1 (3-2008)
Abstract
Abstract: In this paper solid state reduction of high carbon ferrochromium-chromite composite pellets in the temperature range of 900-1350°C was investigated. A two stage reduction mechanism is proposed. The first stage is likely to be controlled by the chemical reaction with activation energy of 127.2kJ/mol. In the second stage, solid state diffusion of carbon through the reaction product layer is suggested to be rate controlling. The activation energy of this stage was calculated to be 93.1kJ/mol. The reduction process was found to be favored by high temperatures as well as high vacuum. The results also show that pre-milling of initial mixture has a negative effect on the reduction degree.
Effect of Calcination Kinetics and Microwave Sintering Parameters on Dielectric and Peizo-Electric Properties of(K0.5Na0.5) NBO3 Ceramics
M. Krishna, R. Nandini, A.v. Suresh, K. Narasimha Rao ,
Volume 15, Issue 2 (6-2018)
Abstract
An efficient solid-state approach was established to synthesize (K0.5Na0.5) NbO3 ceramics using calcination kinetics and microwave assisted sintering. Milling of carbonate and oxide raw materials were carried out for 15h to obtain homogeneous nano particles. The crystallite size of 5.30 nm was obtained for the KNN system after calcination through optimized parameters and observed to be stoichiometric in nature. The obtained nano particles showed phase transition from orthorhombic to tetragonal crystal structure without any secondary phases. The high relative density and tetragonality ratio of KNN ceramics obtained through optimized sintering parameters yielded with significant piezoelectric and ferroelectric properties.
 

The Study of Structure and Transitional Phases in B0.95Bi0.05Ti1-xFexO3 Ceramics Synthesized by Solid State Route
Najwa Gouitaa, Lamcharfi Taj-Dine, Bouayad Lamfaddal, Abdi Farid, Mohamed Ounacer, Mohammed Sajieddine,
Volume 18, Issue 2 (6-2021)
Abstract
    The structural and dielectric properties of iron and bismuth co-substituted BaTiO3 ceramic with the formula: B0.95Bi0.05Ti1-xFexO3 for x=0.00 to 1.00, synthesis with solid state route, were characterized.     The X-ray diffraction results show a tetragonal phase for x=0.00. While for x=0.40 to 0.80 we observed a coexistence of tree phase tetragonal, hexagonal and pseudo-cubic. And at x=1.00 only the pseudo-cubic phase is present and the other phase disappeared. The Raman results indicate the existence of tetragonal band for x≤0.40, and an appearance of characteristic bands of Fe3+ ions for more than 0.40 of Fe content. The SEM micrographs show an increase in grain size with the increase of Fe content and it reaches a maximum at x=0.40.  And the Mossbauer spectroscopy indicates that our samples is paramagnetic at room temperature and that the Fe is   oxidized under Fe3+ with no existence of Fe2+ and Fe4+ ions. The temperature dependence of dielectric permittivity was investigated in the frequency range from 20 Hz to 2MHz. The results show three dielectric relaxation phase transitions from a rhombohedral ferroelectric to orthorhombic ferroelectric (TR-O) then to a tetragonal ferroelectric phase (at TO-T), and finally to cubic paraelectric at the Curie temperature (TC).  In addition, the temperature of phase transition shifted to the lower temperature with the increase of Fe content for all the phase transitions. And the maximum of dielectric permittivity increases for TR-O while for TT-O and Tm phases transitions, it reaches a maximum at x=0.60 and x=0.80 respectively and then decreases.

Investigation of the Effect of Titanium Dioxide and Aluminum Titanate on Physical, Mechanical, and Microstructural Properties of Synthesized Cordierite
Amir Hojjati Lemraski, Ali Sedaghat Ahangari Hossein Zadeh, Rahim Naghizadeh, Hudsa Majidian,
Volume 21, Issue 4 (12-2024)
Abstract
Cordierite ceramics are of interest for various applications due to their properties such as low thermal expansion coefficient and high thermal shock resistance. However, due to the narrow range of sintering temperature, attempts have been made to synthesize it using different additives. In this way, titania and tialite have been added in different amounts to the initial raw material mixture (talc, kaolin, and synthetic alumina). In this research, the initial powders (talc, kaolin, and synthetic alumina) were mixed in a planetary ball mill using different amounts of TiO2 and tialite. The mixtures were sintered at 1250, 1300, and 1350 °C for 3 h. X-ray diffractometry and fluorescence, thermal analysis, microstructural observation, density, and cold compressive strength (CCS) were used to evaluate the sintered samples. Phase analysis revealed the presence of the cordierite phase along with small amounts of spinel. With increasing sintering temperature and titania addition, the amount of spinel decreased and the amount of cordierite phase increased. The real density increased with increasing titania additive content, but at higher titania contents, microcracks were observed in the SEM micrographs. By adding 15 wt% of tialite to the initial batch, the compressive strength has been increased by 88% compared to the pure cordierite sample.
Page 1 from 1     

© 2022 All Rights Reserved | Iranian Journal of Materials Science and Engineering

Designed & Developed by : Yektaweb